Fantasy WargameEst. 2015

Age of Sigmar Miniature Scale for 3D Printing

Age of Sigmar shares its 32mm heroic baseline with modern Warhammer 40k, which makes conversions predictable once you know where a file started. Old Warhammer Fantasy sculpts measure closer to 28mm, so the recurring question is whether your printed hero should tower over the old infantry block or sit level with it.

Skip to content

What scale am I actually printing?

Miniature Scale
32mm
Ratio Equivalent
1:50
Measurement
eye level
Eye Level Height
32.0mm

AoS uses the same 32mm heroic scale as Warhammer 40k Primaris. Older Warhammer Fantasy miniatures (pre-2015) were 28mm heroic and remain usable in Age of Sigmar and The Old World, though they sit slightly shorter than modern sculpts.

Publisher: Games Workshop·Base Sizes: 25mm, 32mm, 40mm, 50mm, 60mm, 80mm, 100mm, 120mm

I treat Age of Sigmar conversions in two buckets. Files designed for the current 32mm range print as-is, while classic pre-2015 Fantasy sculpts and the many '28mm fantasy' STLs get scaled up to 114.3% to match. It is the same number as 40k because both ranges share the heroic 175cm baseline.

AoS models have dramatic poses — flowing cloaks, extended banners, weapon arms swung wide. I always check the slicer's bounding box after scaling because a 14% upscale on a wide pose can push a model past the build plate on small beds. I plan orientation before I commit to supports.

Deep Dive: Old Fantasy, new plastic — the 28mm to 32mm jump

Age of Sigmar sits at 32mm heroic, but most Fantasy collections are full of older 28mm models. Knowing which side of that line your STLs sit on is the whole game when you are printing a mixed AoS force.

Where AoS Sits in Scale

Every new Age of Sigmar release since 2015 is 32mm heroic scale, measured to the eyes — the same convention as modern Warhammer 40k Primaris. Older Warhammer Fantasy Battle miniatures (pre-2015) are 28mm heroic. Both ranges still share tables in AoS, and the size gap is part of the range's history.

Conversion Formula Slicer %
Old Fantasy (28mm) → Modern AoS (32mm)32 ÷ 28114.3%
Modern AoS (32mm) → Classic Fantasy (28mm)28 ÷ 3287.5%

Mixing Old Fantasy and New Plastic

If your force is mostly new plastic, treat 32mm as your anchor and scale any older 28mm Fantasy STLs up at 114.3%. If you are printing a classic regimental army to sit next to 2015-era sculpts, you usually want to keep it at 32mm to hold the line — an undersized rank reads instantly across the table.

The reverse matters too. A modern AoS STL dropped into a classic 28mm collection will tower over the old metal heroes; bring it down at 87.5% if you want it to blend in.

FDM Settings for AoS

Model Type Nozzle Layer Height Notes
Characters and heroes0.2mm0.06mmSharpest edges on armor and faces
Rank-and-file infantry0.4mm0.08mmGood balance of speed and detail
Monsters and centerpieces0.4mm0.1mmBig surfaces hide layer lines well
Terrain0.4mm0.2mmUse grid infill for strength

Scaling Centrepiece Models

Big centerpiece monsters are where AoS scale really shows. If a dragon or daemon STL is designed for a smaller lane and you want it to dominate the board, the validated steps up from the 32mm lane are what I reach for: 234.4% takes a 32mm hero into full display territory, and 109.4% steps it up to the Legion and MCP lane for a slightly larger presence next to those systems.

Common AoS Scaling Mistakes

  • Printing 28mm Fantasy STLs at full size in a 32mm army. If the sculptor says "28mm," you need the 114.3% step to sit level with modern plastic.
  • Running a 0.4mm nozzle on character faces. AoS heroes carry most of their personality in the face and helmet trim — swap to a 0.2mm nozzle at 0.06mm layers.
  • Measuring to the top of a helmet. Scale is set by eye level. A tall helmet or hair tuft will give you a misleading bounding box — measure foot to eyes in the slicer.

Scale Conversions for AoS

Slicer percentages for converting between Warhammer Age of Sigmar and other common miniature scales.

Scale conversions for AoS
ConversionDescriptionSlicer %
28mm → 32mmOld Fantasy to Modern AoS114.3%
32mm → 28mmModern AoS to Classic Fantasy87.5%
32mm → 35mmTabletop to Legion Scale109.4%
32mm → 75mmTabletop to Display234.4%

Printing these minis on FDM

Character models get a 0.2mm nozzle at 0.06mm layers for clean edges on armor and chainmail. Centerpiece models like Morrknul and Nagash benefit from the same profile on the faces. FDM handles terrain and large monsters well at 0.1mm layers.

All settings tested on my Bambu Lab A1 Mini with PLA. Your printer may want something different — always print a test piece first.

Frequently Asked Questions

What scale is Age of Sigmar?
Age of Sigmar uses 32mm heroic scale, the same baseline as Warhammer 40k Primaris. Modern sculpts are designed to this size.
How do I convert old Warhammer Fantasy STLs to AoS?
Scale pre-2015 28mm Fantasy sculpts up by 114.3% to match current Age of Sigmar. The two ranges otherwise show a noticeable height gap.

Warhammer Age of Sigmar and all related names, ranges, and units are trademarks of Games Workshop. STLACCESS is an independent hobby project — not affiliated with, endorsed by, or sponsored by any game manufacturer or publisher. Names appear only to identify miniature scales and printing settings; no branded files, models, or artwork are hosted here.Full trademark notice

Time to check the scale before you commit to a long print.

Launch the STL scale calculator