Sci-fi Skirmish WargameEst. 2018

Star Wars: Legion Miniature Scale for 3D Printing

Legion sits at a 35mm eye-level scale, noticeably larger than Warhammer 40k but smaller than Shatterpoint. This in-between size catches people out because a Stormtrooper labelled '35mm' measures about 40mm to the top of its helmet — so the number on the box does not match the ruler.

Skip to content

What scale am I actually printing?

Miniature Scale
35mm
Ratio Equivalent
1:47
Measurement
eye level
Eye Level Height
35.7mm

Legion's 35mm designation refers to eye-level measurement — a Stormtrooper's eyes sit 35.7mm above the base. The full miniature (top of helmet) reaches about 40mm. This is 1:47 scale based on a 1678mm eye-height reference. Bandai and Revell sell compatible Star Wars kits at 1:48 scale.

Publisher: Atomic Mass Games·Base Sizes: 27mm, 50mm

When I scale Legion STLs I keep the eye-level reference front of mind. A file built for 32mm that I want to run as a Legion trooper gets scaled up to 109.4%. The smooth armor surfaces of Stormtroopers and Clones show layer lines easily, so the profile choice matters as much as the percentage.

Legion shares its 1:47 ratio with common sci-fi model kits around 1:48, which is useful for vehicles. I treat the 1:35 to 1:48 adjustment as a one-step conversion and verify the hull sits well next to my infantry before printing the chassis.

Deep Dive: 35mm eye level — why Stormtroopers tower over Space Marines

Legion is 35mm to the eyes (35.7mm on my 175cm baseline), which puts it bigger than Warhammer 40k and smaller than Shatterpoint. Getting proxies to match means working from that eye-level number, not the top of the helmet.

What 35mm Actually Means

Legion's 35mm designation is an eye-level measurement. A Stormtrooper's eyes sit 35.7mm above the base, and the full miniature reaches about 40mm to the top of the helmet. That works out to roughly 1:47 scale on a 1678mm eye-height reference — and it is why Bandai and Revell's 1:48 Star Wars kits sit so close to the range.

The takeaway: measure to the eyes in your slicer. If you measure to the top of the helmet you will undersize every proxy.

Converting GW-Scale Proxies

Conversion Formula Slicer %
GW (32mm) → Legion (35mm)35.0 ÷ 32.0109.4%
Legion (35mm) → GW (32mm)32.0 ÷ 35.091.4%

Most third-party Legion proxies are sculpted at 32mm heroic. Print those at 109.4% and lock uniform scaling so the proportions stay intact.

Legion vs Classic 28mm

The jump from classic 28mm systems into Legion is bigger than it looks on paper: 125.0% up from 28mm, or 80.0% down if you are scaling Legion STLs for a 28mm game. Either way, the models end up clearly different in bulk, not just height.

FDM and Smooth Armor

Stormtrooper and Clone Trooper armor is made of smooth, unbroken panels — exactly the surface where FDM layer lines show. I print infantry at 0.06mm layers or finer, and vehicles like the AT-ST and AT-RT at 0.1mm. When I scale a proxy, I enable the chain-link lock in my slicer so the ratio stays uniform across all three axes.

Common Legion Mistakes

  • Measuring to the top of the helmet. Legion is an eye-level scale — add the helmet and you undersize every print.
  • Mixing Legion with Shatterpoint. Shatterpoint is 40mm. If you want a Legion model to stand with one, the validated step is 114.3% (35mm → 40mm), and even then the bulk reads differently.
  • Trusting a "32mm" label on a Legion proxy. Verify the eye-level height in the slicer before committing to a long print.

Scale Conversions for Legion

Slicer percentages for converting between Star Wars: Legion and other common miniature scales.

Scale conversions for Legion
ConversionDescriptionSlicer %
32mm → 35mmGW Scale to Legion109.4%
35mm → 32mmLegion to GW Scale91.4%
35mm → 40mmLegion to Shatterpoint114.3%
35mm → 28mmLegion to Classic Scale80.0%

Printing these minis on FDM

The smooth armor rewards fine layers — I print at 0.06mm or finer for troopers. Vehicles (AT-ST, AT-RT) print well on FDM at 0.1mm. Hold XYZ locked when scaling so proportions stay intact.

All settings tested on my Bambu Lab A1 Mini with PLA. Your printer may want something different — always print a test piece first.

Other Games at 35mm Scale

These systems use the same miniature scale as Star Wars: Legion. In most cases, miniatures are interchangeable between them — though art style and proportions will still vary by manufacturer.

Frequently Asked Questions

What scale is Star Wars: Legion?
Legion is 35mm eye-level scale (1:47). A Stormtrooper measures about 35.7mm to the eyes and about 40mm to the top of the helmet.
How do I scale a 32mm STL for Legion?
Upscale a 32mm file by 109.4% to reach Legion's 35mm eye level. Keep uniform scaling locked.

Star Wars: Legion and all related names, ranges, and units are trademarks of Atomic Mass Games. STLACCESS is an independent hobby project — not affiliated with, endorsed by, or sponsored by any game manufacturer or publisher. Names appear only to identify miniature scales and printing settings; no branded files, models, or artwork are hosted here.Full trademark notice

Time to check the scale before you commit to a long print.

Launch the STL scale calculator