What scale am I actually printing?
X-Wing uses 1:27 ratio scale, which works out to roughly 59.3mm eye-level and 64.8mm top-of-head for a human-sized reference. Ships vary dramatically in size — a TIE Fighter is small enough to hold in your palm, while a Rebel Transport fills most of the table. Bandai and Revell sell compatible Star Wars model kits at 1:48 scale, which are slightly smaller but work for casual play.
At 1:27 the fighters are large enough for FDM to handle detail well, but the small wings and fins are vulnerable. I print fighters upright on their sterns or with careful orientation so cockpit and panel lines survive, and I use a fine profile for the named fighters players will inspect closely.
The huge size spread — from small A-wings to capital ships — is the real planning challenge. I scale by the 1:27 ratio and then confirm each model fits the build plate before printing, because a capital ship can easily be a multi-plate job.
Deep Dive: 1:27 ships, no infantry to confuse the math
X-Wing is pure ship scale — 1:27 ratio, with no infantry to muddy the reference. It is the cleanest conversion on the site, and the printing advice is all about smooth hulls and big build plates.
The 1:27 Convention
X-Wing is 1:27 ratio scale, used across every ship in the game — no infantry at all. For a human-sized reference that works out to roughly 59.3mm eye level and 64.8mm to the top of the head. Ships range from a TIE Fighter you can hold in your palm to the Millennium Falcon that fills most of the table, so the math stays clean but the print sizes swing wildly.
Printing the Ships
1:27 ships are large enough for FDM to handle detail well. I use a 0.2mm nozzle at 0.08mm layers for cockpit glass, panel lines, and engine details, and a 0.4mm nozzle at 0.12mm layers for large ships like the Falcon when speed matters. Star Wars hulls are smooth and show layer lines easily, so print at the finest layer height you have patience for, and orient engines and cockpits upward to keep supports on hidden undersides.
Reference Conversions
| Conversion | Formula | Slicer % |
|---|---|---|
| 1:48 → 1:35 (quarter scale up) | 45.7 ÷ 33.3 | 137.2% |
| 1:72 → 1:35 (small scale up) | 45.7 ÷ 22.2 | 205.9% |
There is no validated 1:27-to-1:35 pair in the matrix, so when I scale a Bandai or Revell ship kit (1:48) I use the 137.2% reference step and verify against an official X-Wing model.
Matching the Pre-Painted Plastic
The best reference is an official ship on your shelf. Measure its hull length with calipers and scale your printed ship to match — the labels on ship STLs vary as much as any other range. Before you slice a big Rebel Transport or Star Destroyer, check the bed dimensions: these prints can be wide as well as long.
Common X-Wing Mistakes
- Treating the scale like an infantry scale. X-Wing is 1:27 ship ratio — the 28mm/32mm conventions do not apply.
- Scaling every ship to the same length. Weight and class differences are part of the game's balance. Match each hull to its official model.
- Forgetting the bed on large ships. The Falcon and its friends are wide prints. Check bed orientation before slicing.
Scale Conversions for X-Wing
Slicer percentages for converting between Star Wars: X-Wing and other common miniature scales.
| Conversion | Description | Slicer % |
|---|---|---|
| 1:48 → 1:35 | Quarter Scale Up | 137.2% |
| 1:72 → 1:35 | Small Scale Up | 205.9% |
Printing these minis on FDM
Use a 0.2mm nozzle for cockpit and panel-line detail on fighters. Orient wings and fins carefully to avoid support damage, and confirm large ships fit before printing.
All settings tested on my Bambu Lab A1 Mini with PLA. Your printer may want something different — always print a test piece first.
Frequently Asked Questions
What scale is X-Wing?
How do I print an X-Wing ship without support marks?
Star Wars: X-Wing and all related names, ranges, and units are trademarks of Atomic Mass Games. STLACCESS is an independent hobby project — not affiliated with, endorsed by, or sponsored by any game manufacturer or publisher. Names appear only to identify miniature scales and printing settings; no branded files, models, or artwork are hosted here.Full trademark notice
Time to check the scale before you commit to a long print.
Launch the STL scale calculator