Sci-fi Skirmish WargameEst. 2023

Star Wars: Shatterpoint Miniature Scale for 3D Printing

Shatterpoint deliberately chosen a large 40mm scale to give painters expansive, smooth surfaces — so your printed characters need that extra height or they will read as small next to the official line. Bigger scale also means more material and longer prints, which changes how I plan a batch.

Skip to content

What scale am I actually printing?

Miniature Scale
40mm
Ratio Equivalent
1:43
Measurement
eye level
Eye Level Height
40.0mm

At 40mm, Shatterpoint miniatures are the largest standard Star Wars game scale. Atomic Mass Games chose this size to give painters expansive surfaces for blending and highlighting — a deliberate departure from the smaller scales used in Legion and MCP. Characters like Dooku measure approximately 42.75mm total height.

Publisher: Atomic Mass Games·Base Sizes: 32mm, 40mm, 50mm

The scale decision is simple and the pain is real: everything costs more filament and takes longer. When I print Shatterpoint characters I scale 35mm Legion STLs up by 114.3% and 28mm classics up by 142.9%. The larger canvas makes layer lines more visible on the flat armor panels, so I do not skimp on the profile.

Because characters like Dooku top out near 43mm total, I check bed orientation for faces and helmets immediately. Big, smooth surfaces show a single bad support scar far more than a small infantry model would.

Deep Dive: 40mm — the biggest Star Wars scale

Shatterpoint is 40mm to the eyes, a deliberate step up from Legion's 35mm for more painting surface. When I bring a proxy up to that lane, I am scaling against the largest standard Star Wars game on the market.

Why 40mm

Atomic Mass Games chose 40mm for Shatterpoint so painters get large, smooth surfaces for blending and highlighting — a real departure from the smaller scales used in Legion and MCP. Characters like Dooku measure roughly 42.75mm in total height. The tradeoff is real: bigger scale means more filament per model, so I factor material cost before I commit to a full squad.

Bringing Legion and GW Models Up

Conversion Formula Slicer %
Legion (35mm) → Shatterpoint (40mm)40 ÷ 35114.3%
GW (32mm) → Shatterpoint (40mm)40 ÷ 32125.0%

Classic 28mm to Shatterpoint

Bringing a classic 28mm STL all the way up to 40mm is a 142.9% step. That is a large enough jump that I check the model's proportions after scaling — fine detail like hair strands and thin sabers scale up well, but anything sculpted with exaggerated heroic features can start to look cartoonish at this size.

FDM at 40mm

Shatterpoint's big smooth surfaces reward fine layer heights — 0.04-0.06mm with a 0.2mm nozzle for the best finish. 0.08mm is acceptable for the characters and the terrain pieces. I orient helmets and faces carefully so support marks never land on visible panels.

Common Shatterpoint Mistakes

  • Treating 40mm as 35mm. The numbers are close enough that a Legion proxy printed at full size looks noticeably small next to official Shatterpoint sculpts.
  • Scaling Legion proxies down instead of up. If you own Legion STLs and want Shatterpoint, the direction is 114.3% up, not down.
  • Measuring to the top of a hood or helmet. Eye level is the reference. Hooded characters like Dooku make this mistake easy to make.

Scale Conversions for Shatterpoint

Slicer percentages for converting between Star Wars: Shatterpoint and other common miniature scales.

Scale conversions for Shatterpoint
ConversionDescriptionSlicer %
35mm → 40mmLegion to Shatterpoint114.3%
28mm → 40mmClassic to Shatterpoint142.9%
32mm → 40mmGW Scale to Shatterpoint125.0%
1:48 → 40mmModel Kit to Shatterpoint120.1%

Printing these minis on FDM

Print at 0.04–0.06mm layers with a 0.2mm nozzle for the cleanest surfaces on armor panels. Terrain and table pieces tolerate 0.08mm. Orient helmets and faces carefully to keep support marks off visible areas.

All settings tested on my Bambu Lab A1 Mini with PLA. Your printer may want something different — always print a test piece first.

Frequently Asked Questions

What scale is Shatterpoint?
Shatterpoint is 40mm scale, the largest standard Star Wars game scale, with characters like Dooku reaching about 43mm total height.
How big is Shatterpoint compared to Legion?
Shatterpoint is larger. A 35mm Legion STL scales up by 114.3% to match Shatterpoint's 40mm baseline.

Star Wars: Shatterpoint and all related names, ranges, and units are trademarks of Atomic Mass Games. STLACCESS is an independent hobby project — not affiliated with, endorsed by, or sponsored by any game manufacturer or publisher. Names appear only to identify miniature scales and printing settings; no branded files, models, or artwork are hosted here.Full trademark notice

Time to check the scale before you commit to a long print.

Launch the STL scale calculator